Error Code: 27008 System Cant Satisfy the Requested Bandwith. Please Input Again.

This Article Applies to:

TL-WR841N , TL-WDR3500 , TL-WR743ND , Archer C50( V1 ) , TL-WDR4900 , TL-MR3420 , TL-WR941ND , TL-WR843N , TL-WR710N , TL-WDR4300 , TL-WR702N , TL-WR700N , TL-WR841HP , TL-WR1043ND , TL-WR1042ND , TL-WDR3600 , TL-WR842N , Archer C20( V1 ) , TL-WR940N , Archer C7( V1 V2 V3 ) , Archer C20i , TL-WR741ND , TL-WR740N , TL-WR840N , TL-WR810N , TL-WR841ND , TL-WR720N , TL-WR843ND , TL-WR842ND , TL-MR3020 , Archer C5( V1.20 ) , Archer C2( V1 ) , TL-MR3220 , TL-MR3040

Why we need Bandwidth Control?

Inside a normal dwelling network, the bandwidth is shared by all computers. This means whatever computer using high-bandwidth applications, for example torrent programs or other P2P software, will affect the other computers. This may also include negative influence on the performance of the unabridged network. How tin can we avoid this?

The answer isBandwidth Control, which is designed to minimize the impact caused when the connection is under heavy load.  Using Bandwidth Command, we tin can assign a specific minimum or maximum bandwidth for each computer, which ways they have less interference on each other. Please follow the steps below to configure this characteristic.

How to configure Bandwidth Command?

The scenario beneath will have 3 computers sharing 512KbpsEgress Bandwidth and 4MbpsIngress Bandwidth as an case, and explicate how to apply Bandwidth Command to optimize the load respectively.

Scenario:

Instance: ① PC1 often plays online game and downloads files which uses the virtually part of bandwidth.

② PC2 is used for watching movies on the Cyberspace which besides needs much bandwidth.

③ PC3 is used for browsing websites usually, so information technology only needs a few bandwidth.

Please log in to the spider web management interface to setup bandwidth control.

Step ane

Open up the web browser and in the accost bar type in the default access similar : :http://tplinkwifi.net

Note:

Please find the default access on the lesser label of the production.

Step 2

Blazon the username and password in the login page. The default username and countersign are bothadminin lower case.

Footstep 3

Click onBandwidth Command-Control Settings on the left menu .

Note:

For example, if yous have a ADSL Modem, please cull "ADSL" on the line blazon. If yous don't know how to choose theLine Type, please contact your ISP which line type you accept access.

TheEgress BandwidthandIngress Bandwidth should be the  real bandwidth  given by your Internet service provider . ( 1Mbps=1024Kbps )

Pace iv

ClickSalvageto save the Settings .

Step 5

ClickBandwidth Control -> Rules Liston the left folio, you can view and configure the rules .

Stride vi

Click Add New to add a new rule.

IP Range- Single IP address or IP address Range. When you configure the single IP address, the computer with this IP address will get independent given bandwidth. When you configure the IP address range, all computers in the range willshare the given bandwidth.

Port Range- The port arrange of TCP protocol or UDP protocol.

Protocol- Yous tin choose the TCP protocol or UDP protocol or both of them.

Egress Bandwidth  - The max and the min upload speed which through the WAN port, default number is 0.

Ingress Bandwidth - The max and the min download speed through the WAN port, default number is 0.

Note:

You'd meliorate fix static IP Address on your local computers or configure Address reservation on the wireless router in social club to manage hands.

Virtually how to configure TCP/IP properties on your reckoner, please refer to FAQ xiv

Near how to configure Accost Reservation, please refer to FAQ 182

Step vii

According to the need of clients, the bandwidth could be allocated as following.

From the rules, the max Bandwidth can ensure that  PC1 and PC2 can accept upwards all bandwidth when it'south lonely to access the Cyberspace and the min Bandwidth tin can ensure that they take the necessary bandwidth when more than one PC work at the same time.

Note: The amount ofMin Egress Bandwidth and Min Ingress Bandwidth you lot configure should be less than Egress Bandwidth andIngress Bandwidth you configure onBandwidth Command settings page previously.

Step 8

Enable the Bandwidth Control and click the Save button onBandwidth Control Settings to take effect.

Get to know more than details of each function and configuration please go to Download Eyeto download the manual of your product.

Is this faq useful?

Your feedback helps ameliorate this site.

What'south your business organization with this article?

• Dissatisfied with product
• Too Complicated
• Disruptive Title
• Does non employ to me
• Too Vague
• Other

We'd dearest to go your feedback, please let the states know how nosotros can improve this content.

Thank you

We appreciate your feedback.
Click hither to contact TP-Link technical support.

boweharbeadven.blogspot.com

Source: https://www.tp-link.com/ae/support/faq/557/